今日吃瓜热门大瓜网红黑料|星空mv乌鸦在线观看免费|天美麻花星空免费观看乡村版|精品国产免费观看久久久|日中英美日无码Av

進口氟塑料磁力泵-進口磁力泵

GERMANY KAYSEN PUMP CO .,LTD

進口氟塑料磁力泵是應用現代磁力學原理，利用永磁體的磁力傳動實現扭矩的無接觸傳遞的一種新型泵，也就是電機帶動外轉子（即外磁鋼）總成旋轉時，通過磁場的作用磁力線穿過隔離套帶動內轉子（即內磁鋼）總成和葉輪同步旋轉，過流部件全部采用氟塑料制造，可輸送任意濃（強）度的酸、堿、氧化劑等腐蝕性介質，隔離套采用特殊材料制造具有高強度的力學性能，消除了磁力泵存在的磁渦流現象，由于介質封閉在靜止的隔離套內，從而達到無泄漏抽送介質的目的， 解決了機械傳動泵的軸封泄漏，而設計的全密封、無泄漏、無污染、耐強酸、高效節能的新型無泄漏耐酸泵，性能達到國際標準、可替代價格昂貴不銹鋼，特殊合金材料、的化工泵。

進口磁力泵主要特點：

進口氟塑料磁力泵的設計不僅具有普通磁力泵的結構緊湊，外型美觀，體積小，躁聲低，運行可靠等優點，且其過流部件全部采用目前 上耐腐蝕性能*秀“塑料王”(氟塑料)制造，隔離套采用特殊材料制造，具有高強度的力學性能，消除了普通磁力泵存在的磁渦流現象。因此，氟塑料磁力泵可輸送任意濃（強）度的酸、堿、氧化劑等腐蝕性介質而毫不受損。

主要應用：

進口氟塑料磁力泵被廣泛適用于化工、制酸、制堿、冶煉、稀土、農藥、染料、醫藥、造紙、電鍍、酸洗電解、無線電、化成箔、科研機構、國防工業等行業輸送任意濃度的酸性、堿性、油類、毒性液體、稀有貴重液體、易揮發性的化學介質。特別是易漏、易燃、易爆液體的輸送。適用溫度：-50℃～200℃。

使用注意事項：
●因磁力泵軸承的冷卻和潤滑是靠被輸送的介盾，所以*禁止空運轉，同時避免在工作中途停電后再啟動時所造成時空載運轉。
●被輸送介質中，若含有固體顆粒，泵入口要加過濾網：如含有鐵磁質微粒，需加磁性過濾器。
●泵在使用中環境溫度應小于40℃，電機溫升不得超過75℃。
●被榆送的介質應在泵材允許范圍內。氟塑料泵的使用溫度*不能低于零下30℃*不能超過100℃。輸送吸入壓力不大于0.2MPa，*工作莊力1.6MPa，密度不大于1600Kg/m3，粘度不大于30 X10-6m㎡/s的不含硬顆粒和纖維的液體。
●對于輸送液為易沉淀結易的介質，使用后應及時清洗，排凈泵內積液。
●磁力泵正常運行1000小時后，應拆檢軸承和端面動環的磨損情況，并更換不宜再用的易損件。

進口磁力泵故障原因及排除及排除法：

Fluorine-lined magnetic pump

Self-priming magnetic pump

Fluoroplastic magnetic pump

Magnetic vortex pump

Magnetic gear pump

Stainless steel magnetic pump

Fluoroplastics is a new type of pump that uses the principle of modern magnetism to realize the contactless transmission of torque by the magnetic drive of permanent magnets. That is, when the motor drives the outer rotor (ie, the outer magnetic steel) assembly to rotate, the magnetic field is worn by the action of the magnetic field. The isolation sleeve drives the inner rotor (ie, the inner magnetic steel) assembly and the impeller to rotate synchronously. The overcurrent components are all made of fluoroplastic, which can transport corrosive medium of any concentration (strong) degree of acid, alkali, oxidant, etc. The special material is manufactured with high strength mechanical properties, eliminating the magnetic eddy current phenomenon of the magnetic pump. Because the medium is enclosed in the static isolation sleeve, the purpose of the leak-free pumping medium is achieved, and the shaft seal leakage of the mechanical transmission pump is completely solved. The design is a new type of leak-free acid-proof pump with full sealing, no leakage, no pollution, strong acid resistance, high efficiency and energy saving. The performance meets international standards, can replace expensive stainless steel, special alloy materials, imported chemical pumps.

main feature:

The design of the fluoroplastic magnetic pump not only has the advantages of compact structure, beautiful appearance, small size, low noise, reliable operation, etc., and its overcurrent components all adopt the most excellent "plastic king" in the world. Made of (fluoroplastic), the isolation sleeve is made of special materials and has high strength mechanical properties, eliminating the phenomenon of magnetic eddy current in ordinary magnetic pumps. Therefore, the fluoroplastic magnetic pump can transport any concentrated (strong) degree of corrosive medium such as acid, alkali, oxidant and the like without any damage.

main application:

Fluoroplastic magnetic pump is widely used in chemical, acid, alkali, smelting, rare earth, pesticide, dye, pharmaceutical, paper, electroplating, pickling and electrolysis, radio, chemical foil, scientific research institutions, defense industry and other industries to transport any concentration Acid, alkaline, oil, toxic liquid, rare precious liquid, volatile chemical medium. Especially the transportation of leaky, flammable and explosive liquids. Applicable temperature: -50 ° C ~ 200 ° C.

Precautions for use:

●Because the cooling and lubrication of the magnetic pump bearing is based on the shield that is being transported, it is absolutely forbidden to operate in a dry manner, and at the same time avoid the time-and-load operation caused by the power failure after the start of the work.

● If the solid medium is contained in the medium to be transported, a filter should be added to the pump inlet: if it contains ferromagnetic particles, a magnetic filter is required.

● The ambient temperature of the pump should be less than 40 °C during use, and the temperature rise of the motor should not exceed 75 °C.

● The media to be transported should be within the allowable range of the pump. Fluoroplastic pumps should be used at temperatures not lower than minus 30 ° C and not exceeding 100 ° C. The liquid with no suction pressure is not more than 0.2MPa, the maximum working strength is 1.6MPa, the density is not more than 1600Kg/m3, and the viscosity is not more than 30 X10-6mm2/s without hard particles and fibers.

● For the medium that is easy to precipitate and transport, the medium should be cleaned in time to drain the liquid in the pump.

● After 1000 hours of normal operation of the magnetic pump, the wear of the bearing and the end moving ring should be disassembled and the consumables that should not be reused should be replaced.

Causes of failure and exclusion and exclusion:

Failure form Causes of elimination

The pump does not produce water. Pump reversal

2. Inlet pipe leaking

3. Insufficient water storage in the pump chamber

4. The voltage is too high and the coupling slips when starting

5. Suction is too high

6. The valve is not open. Change motor wiring

2. Stop leaking

3. Increase water storage

4. Correction voltage

5. Reduce pump installation position

6. Calibrate or change the valve

Insufficient flow 1. Inhalation tube diameter is too small or fouled

2. Impeller flow channel obstruction

3. Lift too high

4. The speed is not enough. Exchange or clean the inlet pipe

2. Cleaning the impeller

3. Open large outlet valve

4. Restore rated speed

The lift is too low. Excessive traffic

2. The speed is too low. Close small outlet valve

2. Restore rated speed

Too much noise 1. Pump shaft is severely worn

2. Serious wear and tear on bearings

3. External magnetic steel or inner magnetic steel is in contact with the isolation sleeve

4. Dynamic and static ring wear impeller and pump body grinding 1. Replace the pump shaft

2. Replacement bearing

3. Remove the pump head and reassemble

4. Change the static ring

Leakage, gasket damage, replacement gasket

位于Schw?bischGmünd的德國凱森Kaysen泵業有限公司是 *的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持 各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。

德國凱森始終堅持“重質量，講信譽”為宗旨。產品現 全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。

The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.

進口氟塑料磁力泵-進口磁力泵