|
- 品牌：德國KAYSEN
- 貨號：KS5819569
- 發布日期： 2019-10-11
- 更新日期： 2025-08-21
| 外型尺寸 | |
| 貨號 | KS5819569 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
潤滑油泵-油泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
潤滑油泵主要用于各種機械設備中的潤滑系統中輸送潤滑油。交流潤滑油泵垂直安裝在主油箱的頂板上，經 過油泵底部的濾網吸油，泵排油至主油泵進油管及 經冷油器至軸承潤滑油母管，該泵由壓力開關和裝 在控制室內的三位開關控制，出口裝有翻板式止逆 閥，防止油從系統中倒流。
主要特點：
●密封可靠，在長期運轉中密封狀態很穩定，泄露量很小。
●使用壽命長
●摩擦功率消耗小
●軸或軸套基本上不摩損；
●抗震性好，對旋轉軸的振動以及軸對密封腔的偏斜不敏感；
●適用范圍廣，機械密封能用于高溫，低溫，高壓，真空，不同旋轉頻率，以及各種腐蝕介質和含磨粒介質的密封。
主要應用：
可輸送無潤滑性的油料、飲料、低腐蝕性的液體。配用銅齒輪可輸送低內點液體，如汽油、苯等。
潤滑油故障排除：
| 現象 | 產生原因 | 排除方法 |
| 不排油或 排油少 | 1. 吸入高度太高超過額定值 2. 吸入管道漏氣 3. 旋轉方向不對 4. 吸入管道堵塞或閥門關閉 5. 液體溫度低而使粘度增大 6. 齒輪與泵體麿損嚴重 | 1. 提高吸油面或減少管阻力 2. 檢查各接合處是否漏氣或漏液并加石棉等密封村料加以密封 3. 按泵的指示方向糾正轉向 4. 清除堵塞物，開啟閥門 5. 預熱液體，如不可能則降低排出壓力減少排油量 6. 拆卸檢查有關另件并更換之 |
| 密封漏油 | 1. 軸封處未調整好 2. 密封圈磨損，間隙增大 3. 機械密封靜環和動環的磨擦面損壞或有毛刺劃痕等缺陷 4. 彈簧松馳 | 1. 重新調整 2. 造量擰緊螺母，或更換密封圈 3. 更換動靜環或重新研磨 4. 更換彈簧 |
| 噪音或 振動大 | 1. 吸入網或濾網堵塞 2. 吸管伸入油池較淺 3. 管道進入空氣 4. 排出管道阻力太大 5. 齒輪、軸承或側板磨損嚴重 6. 吸入液體的粘度太大 | 1. 清除濾網上的污物 2. 吸入管應伸入油池0.5米左右 3. 檢查各連接之處使之密封 4. 對管道和閥門進行檢查，并排出堵塞之物，或調整管路減少彎頭、閥門等 5. 更換新齒輪、軸承或側板 6. 按第一段第六條處理 |
Lubricating oil pumps are mainly used to transport lubricating oil in lubrication systems in various mechanical equipment. The AC lubricating oil pump is vertically installed on the top plate of the main oil tank, sucks oil through the filter net at the bottom of the oil pump, and the pump discharges oil to the main oil pump inlet pipe and the oil cooler to the bearing lubricating oil main pipe, which is installed by the pressure switch and installed in the control room. The three-position switch is controlled, and the outlet is equipped with a flap type check valve to prevent oil from flowing back from the system.
main feature:
●The seal is reliable, the sealing state is stable during long-term operation, and the leakage is small.
●Long service life
● Friction power consumption is small
● The shaft or sleeve is basically not worn;
● good shock resistance, not sensitive to the vibration of the rotating shaft and the deflection of the shaft to the sealing chamber;
● Wide range of applications, mechanical seals can be used for high temperature, low temperature, high pressure, vacuum, different rotation frequency, as well as a variety of corrosive media and seals containing abrasive media.
main application:
It can transport non-lubricating oils, beverages and low corrosive liquids. With copper gears, it can transport low internal point liquids such as gasoline and benzene.
Lubricating oil troubleshooting:
Phenomenon Causes of elimination
No oil drain or low oil drain 1. Inhalation height is too high and exceeds rated value
2. Inhalation pipe leaks
3. The direction of rotation is wrong
4. The suction pipe is blocked or the valve is closed
5. The liquid temperature is low and the viscosity is increased
6. The gear and pump body are seriously damaged. 1. Increase the oil absorption surface or reduce the pipe resistance.
2. Check the joints for leaks or leaks and seal them with asbestos and other sealed materials.
3. Correct the steering according to the direction indicated by the pump
4. Clear the blockage and open the valve
5. Preheat the liquid, if not possible, reduce the discharge pressure and reduce the oil discharge.
6. Disassemble and inspect the relevant parts and replace them
Sealing oil leakage 1. The shaft seal is not adjusted
2. The seal is worn and the gap is increased
3. Mechanical seal static ring and moving ring friction surface damage or burr scratches and other defects
4. Spring relaxation 1. Readjust
2. Thread the nut or replace the seal
3. Replace the static ring or re-grind
4. Replace the spring
High noise or vibration 1. Jammed in the suction net or filter
2. The straw extends into the oil sump
3. Pipes enter the air
4. Exhaust pipe resistance is too high
5. Gears, bearings or side panels are severely worn
6. The viscosity of the inhaled liquid is too large 1. Remove the dirt from the filter net
2. The suction pipe should extend into the oil pool by about 0.5 meters.
3. Check each connection to seal it
4. Inspect pipes and valves, and discharge blocked objects, or adjust pipes to reduce elbows, valves, etc.
5. Replace new gears, bearings or side plates
6. Processed in accordance with Article 6 of the first paragraph
Cutting submersible sewage pump
Diving flow booster
Submersible mixed flow pump
Submersible return pump
Corrosion resistant sewage pump
Submersible mixer
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們?nèi)娴漠a(chǎn)品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸?shù)?合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
